Firmware SRP-2100 (04.04.2014)

[FireBird]

Sorry but this German translation doesn't make any sense.

[Twilight]

why you don't you ask in english?

twilight

[geodoc]

Ich habe HxD hex Editor ein ID-22010 ein 22110 Dank übergeben Ich habe HxD hex Editor ein ID-22010 ein 22110 Dank übergeben

[geodoc]

Updates does not work because I have an ID 22110 and I have no reception for channels in Belgium despite several request without response to Topfield I can use TMS and it trailed in a cupboard I guess that there must be a firmware that could rectify the problem but which I'm limited with the version for the 22110 I HxD hex editor like to pass an ID a 22010, 22110 Fine thanks

[Sirius]

[quote=""FireBird""]It is possible but you also need to recalculate the checksum of the header of the file, which makes it not trivial. If you know how to handle a hex editor and post the first 10 bytes of the .tfd file, I can post these 10 bytes for the 22110.[/quote]
Is this the information you asked for?
The System-ID seemed to be in byte 5. + 6 (04 +05)., but which bytes are for the checksum?

Code: Alles auswählen

00 08 8A 55 [color=Green]55 FA[/color] 00 64 01 31  => SRP-2100_[color=Green]22010[/color]-2014Apr10.tfd
00 08 8A 55 [color=Green]55 FA[/color] 00 64 01 31  => SRP-2100_[color=Green]22010[/color]-04042014.tfd
00 08 8B 15 [color=Green]55 FA[/color] 00 64 01 32  => SRP-2100_[color=Green]22010[/color]-v115_2013.08.13_WithPRE.tfd
00 08 42 14 [color=Green]55 FA[/color] 00 64 01 2E  => SRP-2100_[color=Green]22010[/color]-2012Mar23.tfd


00 08 7A 64 [color=Red]56 5E[/color] 00 64 01 16  => SRP-2100([color=Red]EU_22110[/color])-2012Apr17_v1.07.01_Dev.tfd
00 08 AB 65 [color=Red]56 5E[/color] 00 64 00 EA  => SRP-2100_[color=Red]22110[/color]-2009Apr17.tfd

[FireBird]

Bytes 2 and 3 are the checksum of bytes 4 to 10. Go to that page, switch "Input type" to hex, enter bytes 4 to 10, click “Calculate CRC” and CRC-16 will be the result you’re after.

[Sirius]

Thanks FireBird

your solution is that geodoc should test this modification:

Code: Alles auswählen

00 08 [color=Blue]60 24[/color] [color=Red]56 5E[/color] 00 64 01 31  => SRP-2100_22010 [color=Red]modified to 22110[/color]-2014Apr10.tfd

[FireBird]

Yepp, that's looking good.

[geodoc]

00 08 6000 3F 6E 4A FE F1 F3 C8 8D D3 59 3C C6 D7 D9 87 C8
00 08 6010 E7 C4 AB B9 D7 28 2F 8E FD F0 DA 8A 6A 9C 71 FE
00 08 6020 C1 CC E5 5C FF A5 33 9B 5C C2 C8 0F 22 EF 9A 15
00 08 6030 46 D8 99 DA B1 F0 39 75 C6 D3 9B FF 15 3A 16 F7

Here is what I have in the lines should add the line

[Sirius]

I did not understand your last post, your hex codes makes no sense.
For example in first line "3F 6E" is not a right System-ID for SRP-2100.


geodoc just do this:

1. Download the latest Firmware for SRP-2100 (ID 22010) April 2014
=> Download here

2. Open the Firmware (.tfd) file in a hex editor (f.e. HEX-Editor MX V6.x)

3. Edit the 4 bytes (blue and red marked) in the first line in the editor and save the changes.

Code: Alles auswählen

00 08 [color=Blue]60 24[/color] [color=Red]56 5E[/color] 00 64 01 31  => SRP-2100_22010 [color=Red]modified to 22110[/color]-2014Apr10.tfd

4. Update the Toppy by USB (your SRP-2100 with System-ID 22110 should now accept this new file)

[geodoc]

The amendment has run the Frimware is accept but it tells me CRC CHECK ERROR

[geodoc]

Well thanks it works remains a reconnect on the satellite and put the card in the decoder I can be the surprise that Belgian strings and French by TELESAT still works thanks

[geodoc]

After putting on the road and research stations the problem of the sound that was not save on ASTRA channels working properly but the problem is still relevant on Hotbird free channels OK but channels such as TF1 A2 FR3 etc. are impossible to look at what are only squares and in addition I have the lyrics reading that appears at the bottom of the image.
If anyone with an idea can be the CAM?
I had hope with this new Firmware to finally use the Topfield.

[Sirius]

[quote=""geodoc""] ... I have the lyrics reading that appears at the bottom of the image.[/quote]
Maybe this can help you:

Disable "first subtitle language" and "Hard of Hearing" in Menu Settings / Language.

[tasman_shn]

[quote=""prusony""]Thank you very much for your reply!
I solved problem:
Just with HEX-redactor added in damaged dump sector of right dump ***.tfd ,
then programming FLASH-chip through BEEPROG,
then soldered chip into place - tuner said "LOAD........E-2",
then load firmware from USB-flash.
Now everything OK! TF work!
Thanks again!
If someone's going this situation - try this dump: http://rghost.ru/6cHhdbYRM[/quote]

I also have same problem. The problems appear when I tried to upgrade firmware using TMS Emergency Procedure.

After the upgrade is completed (END appears on the front panel) then I restart Topfiled TMS SRP 2100. Now the display on the front panel just LOADING The power button on the front panel does not work. O button no response (no lights on)

Is there another way to fix this receiver ?

[matradix]

Sorry falls ich etwas in dem langen Thread übersehen habe. Auch sind manche Links hier Tod.

Ich suche die neueste Firmware für den 2100. Kann mir da jemand weiterhelfen und mir mitteilen wo die zu finden ist, oder mir zusenden? Danke

Gesendet von meinem SM-N910F mit Tapatalk

[macfan]

[quote=""matradix""]Sorry falls ich etwas in dem langen Thread übersehen habe.[/quote]
Stimmt, der Link ist nur 6 Beiträge höher in #750.

Gruß, Horst

[matradix]

Danke Horst!
Dies ist die neueste? Auch inoffizielle hier im Forum berücksichtigt?
Im Eingangspost wird von Firmware vom 13.8.2013 als neueste geschrieben.

[wohliks]

[quote=""matradix""]Dies ist die neueste? Auch inoffizielle hier im Forum berücksichtigt?
Im Eingangspost wird von Firmware vom 13.8.2013 als neueste geschrieben.[/quote]Andersrum gefragt: Hat Dein 2100 irgendein Problem, das Du mit einer anderen als der von macfan vorgeschlagenen Firmware zu lösen hoffst?

Mein 2100 läuft unter der Firmware aus #750 (also Apr 2014) einwandfrei...

[macfan]

[quote=""matradix""]Dies ist die neueste? Auch inoffizielle hier im Forum berücksichtigt?[/quote]
Das ist immer schwer zu durchschauen. Welches Datum hat denn die Firmware aus #450? Die aktuellste, die ich auf meiner Festplatte habe, ist vom 4.4.2014.

Gruß, Horst